How to Troubleshoot Bore Yield and Pressure Loss
AdminA bore that once kept up with household, farm or plant demand can become frustratingly unpredictable: pressure fades, a storage tank fails to recover, or the pump begins cycling on and off. Knowing how to troubleshoot bore yield helps separate a genuine groundwater limitation from a pump, pipework or treatment issue. That distinction matters. Replacing a pump will not restore an aquifer, while drilling deeper will not fix a blocked filter or a leaking delivery line.
Bore yield is the volume of water a bore can supply over time without drawing the water level down beyond the pump intake or the bore’s practical operating limit. It is not simply the maximum flow seen when a pump first starts. A bore may deliver a strong initial flow from water stored in the casing, then decline as the water level draws down. The sustainable yield is what remains after that early reserve has been used.
Start by confirming the actual problem
Before changing equipment, record what the system is doing. A report that the bore has “low pressure” does not automatically mean low yield. Pressure is created by the pump and restricted by the pipework; yield is governed by the bore and aquifer. Both can produce similar symptoms at a tap, but require very different remedies.
Check whether the problem occurs only at high demand, such as irrigation, washdown or several household fixtures operating together, or whether it is present even with one tap open. Note whether the pump runs continuously, trips on overload, cycles rapidly, draws air, or stops after a set time. Compare these observations with normal operation if you have previous records.
A pressure gauge at the pump discharge and a flow measurement at a known outlet give a useful starting point. For larger sites, log pump run time, pressure, flow and tank level over several days. This evidence is far more useful than a one-off observation during peak demand.
Check the easy restrictions before testing the bore
Many apparent yield failures are caused by restrictions after the bore. Work through the system from the pump outlet towards the point of use. Isolate and check treatment equipment, especially sediment filters, cartridge housings, strainers, iron-removal media and UV prefilters. A heavily loaded filter can sharply reduce flow while the bore itself remains capable of supplying water.
Also inspect for partially closed valves, blocked check valves, crushed polyethylene pipe, leaks, damaged pressure tanks and fouled irrigation nozzles. If the pump is installed with a pressure controller, confirm the controller is sensing pressure correctly and is not repeatedly stopping the pump on low-flow protection.
Where a treatment plant has been added since the bore was installed, review the design flow. Treatment equipment creates pressure loss by design, and a system sized for domestic demand may not suit additional stock water, irrigation or process demand. A low-flow membrane, undersized filter housing or restrictive control valve can become the bottleneck.
If practical, test flow directly from a suitable point close to the pump, then repeat the test after the treatment train. A meaningful difference points to downstream resistance rather than bore yield.
Inspect the pump and power supply
A bore pump can lose performance gradually through wear, scale, corrosion, sand damage or electrical problems. A submersible pump that is no longer achieving its duty point may run for longer, produce reduced pressure and resemble a depleted bore.
Compare operating current with the motor nameplate and earlier service readings. Low or unstable voltage, phase imbalance on three-phase systems, failing capacitors on some single-phase arrangements, damaged cable joints and controller faults can all affect pump output or protection settings. Electrical testing should be carried out by a suitably qualified person.
For a pump with a known make and model, compare measured flow and pressure against its pump curve, allowing for the actual total head. Total head includes the vertical lift from the dynamic water level, pipe friction, elevation change and treatment equipment losses. A pump selected when the water level was shallow may become unsuitable if seasonal drawdown is now much greater.
Pump depth matters as well. If the water level has fallen below the pump intake during pumping, the system may lose flow, surge or draw air. Conversely, lowering a pump is not always the answer. It must remain clear of sediment at the base of the bore and within the pump manufacturer’s permitted operating conditions.
Measure static level, drawdown and recovery
The clearest way to diagnose bore performance is to measure the water level before, during and after a controlled pumping test. The static water level is the level after the bore has rested. The dynamic water level is the level while pumping at a known flow. The difference between them is drawdown.
Start with the bore rested for long enough to represent normal conditions, preferably after a low-use period. Measure the static level using suitable bore-level equipment. Then run the pump at a measured, steady flow and record water level, flow and discharge pressure at regular intervals. Continue long enough to see whether the water level stabilises or continues falling.
After the pump is stopped, record how quickly the bore recovers. A stable dynamic level and reasonable recovery suggest the aquifer is supporting that rate. A water level that keeps declining, followed by slow recovery, indicates the pumping rate may exceed sustainable yield.
Do not rely on a short test alone. Some bores appear healthy for 20 minutes but fail after several hours of irrigation or process use. Test duration should reflect the site’s real duty cycle. A domestic bore feeding a storage tank may need a different assessment from a bore supplying a dairy shed, food-processing line or commercial irrigation system.
Look for changes in water quality and bore condition
A fall in yield accompanied by sand, silt, cloudy water or a new change in colour can indicate a bore-screen or bore-development issue. Scale, iron bacteria, mineral deposits and biofouling can restrict screens and reduce water entry into the bore. Fine material entering the pump can damage impellers and block downstream filters.
Changes in water quality may also affect treatment performance. Higher iron, manganese, turbidity or hardness can load filters faster, foul membranes and reduce UV transmittance. If the bore is supplying drinking water, do not assume that a flow problem is only a mechanical problem. Review treatment barriers and verify that the water remains suitable for its intended use.
Bore rehabilitation can sometimes recover performance through cleaning, redevelopment or targeted chemical treatment. The right method depends on the bore construction, screen material, deposits present and water chemistry. Aggressive or poorly managed cleaning can damage equipment or mobilise contaminants, so it should be planned by experienced bore and water-treatment professionals.
Match demand to sustainable supply
A bore can be sound but still be asked to do more than it was designed to deliver. Seasonal groundwater variation, dry weather, neighbouring abstraction and gradual changes in aquifer conditions can reduce available yield. Expanding a home, adding irrigation, increasing livestock numbers or installing a new process line can have the same practical effect.
The most reliable solution is often to reduce the instantaneous demand on the bore rather than force a higher pumping rate. A correctly sized storage tank lets the bore pump at a sustainable rate over a longer period, while a booster pump supplies higher short-term demand to the property or process. This arrangement can protect the bore, reduce pump cycling and give the site a useful buffer during dry periods.
For irrigation, divide demand into zones and schedule watering to allow tank recovery. For commercial or industrial sites, assess peak demand, average daily volume, required reserve and the consequences of interruption. The answer may be storage, a revised pump duty, treatment upgrades, an alternative supply, or a combination of these measures.
When professional investigation is warranted
Bring in specialist support when the pump is drawing sand or air, water levels are falling rapidly, the bore has materially changed after years of stable operation, or the supply supports drinking water, production or a community service. A structured investigation can combine bore records, pump testing, flow and level logging, water analysis, treatment review and practical options for rehabilitation or system redesign.
Franklin Water can assess the full system rather than treating the pump, bore and treatment plant as separate problems. That approach helps identify whether investment should go into pump controls, storage, filtration maintenance, bore rehabilitation or a redesigned supply arrangement.
A bore is a working water source, not an unlimited tap. Measure its behaviour, protect it from excessive drawdown and design the rest of the system around the water it can sustainably provide. That gives you a more dependable supply and clearer decisions when conditions change.